RalliTEK engineered these direct replacement rear HD endlinks to work with factory or aftermarket sway bars. Made out of durable polyurethane bushing, and a steel shaft that was increased by 30%, the RalliTEK endlink provides less movement among the sway bar.
Features:
30% thicker material than the factory.
Outlast and outperform OEM links.
OEM replacement
The product contains 2 rear endlinks
Includes lubricant
The factory endlinks in your Subaru's rear control arm are made out of soft rubber. Over time the rubber becomes weak allowing more "slack" in the rear suspension. RalliTEK noticed that the factory endlinks were a little weak and didn't allow adjustment for raised or lowered vehicles. This laid the foundation for the design requirements. A direct replacement HD endlink that will work with factory or aftermarket sway bars at different ride heights. Performance needed to be precise enough for the track and strong enough to take on the trail.
RalliTEK HD heavy-duty endlinks are designed to outlast and outperform your factory sway bar endlinks.
RalliTEK HD endlinks features, material 30% more rigid than factory, steel alloy construction, polished steel ball and socket(not plastic like factory), and adjustable length to dial in the perfect bar angle at any ride height. These are a perfect addition when upgrading your sway bars or when changing your ride height.
great design overall and well packaged. The supplied grease was just the right amount to lubricate the bushings and inner crush tube of the lower mount. I recommend folks anti-seize both end studs before installing into the turnbuckle or wrap it up with silicone tape after height is adjusted. I do think two washers should be supplied for each endlink in order to properly secure the top side ball joint to the swaybar arms and spread the load. The stud stop was of very small diameter and may not clamp well on some swaybar arms that have oversized holes.
K
Kevin W.
Excellent Upgrade
I have really enjoyed the improvements these made and the quality is top notch!
RalliTEK branded products are warranted to the original owner against manufacturing defects in materials and workmanship for the lifetime of the product.
If a RalliTEK branded product covered by this warranty fails due to a manufacturing defect we will repair the product, without charge, or replace it at our discretion. This policy covers only original, unaltered, and unmodified materials and workmanship. This warranty does not cover damage caused by incorrect installation, accident, improper care, negligence, normal wear and tear, or the natural breakdown of colors and materials over extended time and use. Damage not covered under warranty may be repaired for a reasonable rate and a fee will be charged for return shipping.
For warranty evaluation, please contact RalliTEK Customer Service at (503) 619.0055 or info@rallitek.com to obtain a return authorization. Once this step has been completed, your product must be returned directly to theRalliTEK Warranty Department, 13339 NE Airport Way, Suite 500, Portland, OR 97230. All shipping to the Warranty Department must be pre-paid and insured. RalliTEK will not be liable for damaged or lost inbound packages.
NOTThis warranty is only available within the United States or Canada
This warranty gives you specific legal rights; you may have other rights, which vary from state to state.
This warranty does not cover products sold by RalliTEK that are not RalliTEK branded products.
The RalliTEK website sells discontinued, special markup, and slightly blemished products at significant discounts as 'factory seconds' products. This warranty does not automatically cover products purchased as factory seconds. RalliTEK reserves the right to determine if any warranty applies on a case-by-case basis for factory second parts. If approved, the RalliTEK Warranty Department may repair factory second products for a reasonable charge and applicable shipping charges.
Non-RalliTEK branded products do not have any written or implied warranties. Products on RalliTEK.com are sold with the warranty applied directly from the manufacturer. The customer must contact the product brand manufacturer for any warranty details. All products sold by RalliTEK are intended for off-road and/or race use only, as suggested by the manufacturer, and should be installed and set up by professional service centers only.RalliTEK is not responsible for any product failure or failure due to installation. Should a warranty claim arise, the customer and the manufacturer will handle all warranty issues directly.
There is no warranty on high-performance or race-related parts due to the nature of usage.
No payment or reimbursement shall be made for installation, removal, transportation, or other charges. The remedies outlined in this instrument are exclusive and the liability of RalliTEK with respect to any sale shall not exceed the price of the product on which the liability is based.
EXCEPT AS STATED OTHERWISE IN THIS WARRANTY, RalliTEK MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. RalliTEK shall not, in any case, be liable for special, incidental, consequential, indirect, or other similar damages arising from any breach of these warranties even if RalliTEK or its agent has been advised of the possibility of such damages. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. This warranty is governed by the laws of the State of Oregon.
great design overall and well packaged. The supplied grease was just the right amount to lubricate the bushings and inner crush tube of the lower mount. I recommend folks anti-seize both end studs before installing into the turnbuckle or wrap it up with silicone tape after height is adjusted. I do think two washers should be supplied for each endlink in order to properly secure the top side ball joint to the swaybar arms and spread the load. The stud stop was of very small diameter and may not clamp well on some swaybar arms that have oversized holes.
K
Kevin W.
Excellent Upgrade
I have really enjoyed the improvements these made and the quality is top notch!